| Model Identification | |
| Full Model Number | RPS0050MD561E101 |
| Product Line | Temposonics® RPS (Industrial Non-Contact Linear Position Sensor) |
| Mechanical Specifications | |
| Sensing Length (Stroke) | 50 mm (1.97 inches) |
| Housing Material | Anodized Aluminum (EN AW-6063-T6) |
| Sensor Rod Material | Stainless Steel 1.4305/AISI 303 |
| Protection Rating | IP68 (Submersible to 1.5m, 24h) / IP69K (Steam-jet proof) |
| Max. Rod Bending Load | 10 N |
| Electrical Specifications | |
| Supply Voltage | IO-Link Mode: 18-30 VDC
Analog Mode: 15-30 VDC |
| Current Consumption | ≤ 100 mA (IO-Link active) |
| Output Signals | |
| Primary Output | IO-Link 1.1 (Compliant with IEC 61131-9) |
| Secondary Output | 0-10V Analog Voltage (Fallback during IO-Link disruption) |
| IO-Link Data Rate | COM2 (38.4 kbaud) |
| Analog Output Load | ≥ 10 kΩ |
| Performance Metrics | |
| Linearity Error | ±0.01% Full Scale (FS) (±0.005 mm over 50 mm stroke) |
| Repeatability | ≤ 0.001% FS |
| Resolution | 0.005 mm (Digital) / 12-bit (Analog) |
| Response Time | ≤ 0.5 ms (Analog), ≤ 2 ms (IO-Link cycle time) |
| Update Rate | 2 kHz (Internal measurement) |
| Temperature Coefficient | ±0.005% FS/°C (Gain & Offset) |
| Environmental Ratings | |
| Operating Temperature | -40°C to +85°C (-40°F to +185°F) |
| Shock Resistance | 100 g, 11 ms (IEC 60068-2-27) |
| Vibration Resistance | 20 g (10–2000 Hz per IEC 60068-2-6) |
| Magnet & Sensing | |
| Magnet Type | External Float Magnet (PPS-Encapsulated, Included) |
| Max. Sensing Gap | 25 mm (from rod centerline) |
| Max. Target Speed | 10 m/s |
| Connections | |
| Electrical Interface | M12 × 1, 5-pin A-coded (IO-Link + Analog) |
| Pin Configuration | 1: IO-Link C/Q, 2: GND, 3: 0-10V, 4: Vs+, 5: IO-Link L+ |
| Cable Length | 1 m (Shielded PUR, indicated by "E1" suffix) |
| Compliance & Safety | |
| EMC Standards | EN 61000-6-2 (Immunity), EN 61000-6-4 (Emissions) |
| Certifications | CE, RoHS 3, REACH |
| Communication Protocol | IO-Link V1.1, Profile 1.0 (Sensor) |
| Smart Features | |
| Parameterization | Via IO-Link: Teach-in, Range Adjustment, Fault Configuration |
| Diagnostic Data | Magnet Status, Temperature, Signal Strength, Supply Voltage |
| Process Data (IO-Link) | Position, Velocity, 16-bit Status Word |
| Special Options (E101) | |
| Connector Type | M12 A-coded Socket (Female) |
| Sealing | High-Chemical Resistance Seals (Suitable for Coolants/Oils) |
| Calibration | Factory-Calibrated for 50 mm Stroke ±0.01% FS |
| Application Scope | |
| Typical Use Cases | Precision Valve Control, Small Actuators, Fill-Level Monitoring |
| Media Compatibility | Hydraulic Fluids, Coolants, Water-Glycol, Mild Solvents (Avoid Strong Acids) |
| MTBF | > 100,000 hours (IEC 61709) |
